Introduction

The $99 Arty Evaluation Kit enables a quick and easy jump start for embedded applications ranging from compute-intensive Linux based systems to light-weight micro-controller applications.
Designed around the industry’s best low-end performance per-watt Artix®-7 35T FPGA from Xilinx. Arty kit features the Xilinx MicroBlaze™ Processor customizable for virtually any processor use case
Artix-7 FPGAs deliver high performance for cost sensitive applications. The ARTY evaluation board is a complete system, packaging all the necessary functions and interfaces neededfor an embedded processor system onto a small footprint. This board is the perfect solution for designers interested in exploring the MicroBlaze soft processor or Artix-7 35TFPGAs.

This WiKi document explains about the FreeRTOS Webserver demo on ARTY and targeting the Artix-7 35T FPGA. This demo uses the MicroBlaze soft-core processor,
a 10/100 Ethernet MAC, DDR3 Memory controller, and GPIO soft cores in Artix7 FPGA.
This Wiki document also explains the step by step procedure to execute the demo in JTAG debug mode and you can also boot from QSPI using the SREC boot loader.

Following is the block diagram of the demo
freeRTOSWebServer.jpg

freeRTOSWebServer2.jpg

Required Hardware

Required Software and Tools

Recommended Software and Tools

  • Tera Term terminal program (any terminal program should work, but Xilinx has tested this application with TeraTerm)

Reference Design Files

The demo design Archive has the following directory structure:
freeRTOSWebServer3.jpg

  • \HW - Contains vivado hardware design files.
  • \SW - Contains FreeRTOS_Lwip_Webserver_Demo, it has webserver application and Echo server for jtag boot mode.
  • \ready_for_download - Contains executable files for ready to test through XMD.
  • \Workspace - This is an empty folder, user can import SDK SW folder workspace to this location.
  • \memfs - Contains webserver image files and packaged library with name libmfsimage.a.
  • \Arty_Board_Definition_Files - Contains ARTY Vivado board part files, these files are needed to create the hardware project using the Vivado.
    • By default vivado 2015.2 installation not having ARTY Vivado board files. There is a doc folder which contains the steps on how to add board files to Vivado Project.
Powering on Arty and connecting the USB and Ethernet Cable
  1. Connect the Ethernet and micro-USB cables to the ARTy board and your PC
(Note: ARTY can get it's power for this demo from the USB port, so, while optional, there is no need to connect external power supply for this demo)
  1. artyCables.jpg

Sting up Static IP address
  1. Assign a static IP address to the Ethernet interface on the host PC/Laptop. (Refer below image)
    1. Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Change adapter settings > Local Area Connection
    2. It will open Local Area Connection Status Window, In General tab, click on properties and Select Internet Protocol Version 4 (TCP/IPV4) properties
    3. Select Use the following IP address.
      1. Enter this address in IP address area: 192.168.1.xx (Ex: 192.168.1.100)
      2. Enter this address in Subnet mask area: 255.255.255.0
    4. Click OK, then Done
freeRTOSWebServer4.jpg

Extract the Zip File:
(Remember where you save it, we will be using this later in the walkthrough)
(Ctrl + Scroll to zoom in & out)
1x.png

Browse for the ..\Artix7_35T\workspace folder (varies depending on where you download it.)
2x.png


3x.png

Serial>Serial port
4x.png

Change the COM to the correct Port, make sure it is the same as shown in the next step. And set the baud rate to 115200.
5x.png

Connect to a Serial Port in the SDK. Double check all of the information is matching.
6x.png

Verifying the USB COM port that has been assigned by the PC.
1) Open the START menu
2) Select my computer
3) Right mouse and select Properties
4) Select Device Manager
5) See that the ARTY board is connected to the USB Serial Port (COM 24).
In my case it is COM 24. Yours will probably be different. Note the COM port number, as you will need it when setting up the java GUI


7.JPG
Reset board by pressing the PROG button at the top left of the board.
7x.png

File>Import
8.png

General> Existing Projects into Workspace
9.png8.png

Browse for the ..\Artix7_35T\SW folder (varies depending on where you download it).
10.png

Check “Copy projects into workspace”, and then click Finish
11.png

Next: Xilinx Tools> Program FPGA
12.png

Ensure the Bitstream and BMM/MMI File look similar. Then click program.
13.png

Right click on FreeRTOS_LWIP_Webserver_Demo>Run As> Run Configurations
14.png

Click the Xilinx C/C++ application (System Debugger) option for a pull down. Then click on the pull down option: FreeRTOS_LWIP_Webserver_Demo Debug, then Run.
15.png

Go to Tera Term, and after the code has been run, the hyperlink should appear. Click on it, or copy it into an internet browser.
16.png

Run the demos and experiment with ARTY
17.png

Finished!